- MAC DVD PLAYER NOT EJECTING DRIVERS
- MAC DVD PLAYER NOT EJECTING DRIVER
- MAC DVD PLAYER NOT EJECTING WINDOWS 10
- MAC DVD PLAYER NOT EJECTING SOFTWARE
This Disk-Changed error is therefore passed to any utility that is in the drive handling chain (In this case, only AnyDVD is listed: That is no longer handled by Microsoft (with the removal of their DVD Player Support). My own analysis (as shown above) points to the fact that the DVD drive generates a Disk-Changed error when a NON-Blank is inserted Which means the developers are not looking at the ERROR handling path of AnyDVD. The problem is when a NON-Blank DVD is inserted and AnyDVD kicks in. So you can see, the moderator did not fully read this thread. It stays inactive when a blank disc is inserted. If you are referring to blank media, AnyDVD is not involved at all in the burning process. Hope this helps the developers figure this out because it is getting annoying having to shut down Nero to increase my chance of getting the DVD to stay in the drive (1 in 4 chance that it will not with Nero shut down). The DVD drive is an LG Blueray player, DVD burner 16X (though I always burn at 8X) The what make of blank DVD does not matter with this problem. I use Amazon DVD's, Philips and Maxells as my blanks.
MAC DVD PLAYER NOT EJECTING WINDOWS 10
The error code Unknown as it does not appear on the Windows 10 Popup: I am sure that some of the error codes were handled by windows before and not AnyDVD.Īny unhandled exception will be returned to the Windows OS and therefore generate the Popup.
MAC DVD PLAYER NOT EJECTING SOFTWARE
This could even be due to Windows 10 taking out the native DVD support and leaving the control hanging, therefore dependent on the software (like AnyDVD) to control all error handling.
MAC DVD PLAYER NOT EJECTING DRIVERS
This leads me to believe that one of the drivers that watches when a DVD is put in gets an error code right away that, in-turn, causes the auto-eject. The problem is sporatic when Nero is not active but when Nero has just used the Drive, the problem is repeatable more often than not (again, nothing is 100 percent of the time). I went into system-:>Device Manager and removed the DVD drives and rebooted.
MAC DVD PLAYER NOT EJECTING DRIVER
There is a driver conflict with Windows 10 and AnyDVD. Usually will not stay in and even waiting 20 seconds will not work.ġ4) I HAVE to shut down Nero and wait just a bit to get the Fresh non-blank DVD to stay in the drive. Insert blank, usually stays in (not always). I can usually wait 20 seconds or so and then get them to stay in.ġ3) Back to DVD to rip stays in, 1st Non-Blank will stay in.
I uninstalled it.Ĩ) Placed 8 consecutive, different DVD's (non-blank) in the drive and they all stayed.ġ0) First two DVD's stayed in, Third & Fourth were Auto-Ejected, Fifth stayed in.ġ1) Once they Auto-Eject. It Auto-Ejected!!!ħ) So at this point the only thing currently installed that I use for DVD's is AnyDVD. It stayed in OK, Ejected it.Ħ) Placed yet another DVD into the drive. So uninstalled Nero AGAIN.ĥ) Placed the same DVD into drive. Ejected and tested it.Ĥ) Placed a Different DVD into drive. DVDShrink Read the DVD OK.ģ) Put in a blank, it stayed. (Placed DVD in drive, stayed, ejected it, put in a different one and it auto-ejected).Ģ) Reinstalled Nero (Did not start it). (The DVD will be sucked in during boot and stays in).ġ) Uninstalled Nero. It will usually eject and keeps ejecting until I do one of the following:Ī) Terminate Nero and wait for about 20 seconds.ī) Terminate AnyDVD (Once the DVD goes in and stays, I can restart AnyDVD and it is OK then).Ĭ) Reboot the computer. Usually goes fine but once in awhile I get a coaster (1 out of 40 or so-That is OK for me).ĥ) I take the freshly burned DVD out and test it.Ħ) I put in another DVD (ex: Scrubs S7, D2). This USUALLY goes OK but sometimes it will eject "Insert disc".Ĥ) I use Nero to burn a DVD. Goes fine.ģ) I then take the DVD out and put in a blank. I have the same problem but since AnyDVD is not ripping or reading a dvd at the moment, no log file from it.ġ) I put in a DVD into ANYDVD on a fresh boot, goes in fine,Ģ) I use DVDShrink to read the DVD into the computer.